Adding depth to fused glass 2

Early spring saw me thinking more sculpturally and starting to obtain slight relief by fusing over fibre blanket forms. As the relief is on the back of the work it only works with transparent glass and preferably back lighting. The technique is sometines refered to as bass relief, although strictly speaking the form should then be on the front face of the artwork.

First experiments were with slumping bottles, including giving some form to an otherwise flat plate that was difficult to pick up from a table.

Once happy that the technique worked I tried fusing glass over simple shapes.

Just before leaving to get the boat ready for the summer season I tried a much more complicated design. Again, the work was fused directly onto the pattern pieces but with so many small elements some moved with the glass as it formed. The overall patern is recognisable as a celtic knot but I was not happy with the detail. I could have fused first, then slumped the glass over the pattern, but would not have been able to relate coloured elements directly to the design.

This piece uses coarse adventurine frit, streaky green transparent and clear glass.

My final piece of the winter season was a bit of fun. As with all my suncatchers the suspension point for the single wire is cast in the glass. With this piece its location was something of a guess, as I could not find the balance point until it was fused. Fortunately my guess proved to be right!

Adding depth to fused glass 1

After my first few firings with the kiln I wanted to add depth to my work.

The easiest way was to fuse clear glass onto the work. This gives a lighter colour when overlaid on transparent glass as in this suncatcher.

Setting up the glass

Fired suncatcher showing lighter shades under the clear glass

There is no change in the underlying colour on opaque glass, but depth of the piece is apparent with shadows and refraction at the edges of the clear glass inlay.

Trials and Tribulations

My first attempt at an enclosed form. The idea is to mix different blue glasses with clear bevels to throw coloured highlights when used as a suncatcher.

First step was to build two pyramids. These were then cleaned ready for finishing. They were then joined together. My fear was that the solder would melt through the join and fall inside the piece.

Sure enough, after carefully tacking and then closing the joint all the way around, I ran a full bead to finish the seam. Only one side then flowed through the joint and created a blob across the opposite edge. My first reaction, working on the principle that solder flows towards the heat was to melt the joint solder over the blob, holding this edge downwards so that the solder could fall out. This worked and cleared the blob that was over the foil. However some had solidified on the glass surface and this did not move.

Only one thing to do - melt all the solder around the joint to separate the two pyramids. It took a while, and damaged much of the copper foil. The positive result was that I devised a technique that should  avoid the solder flow problem. Sure enough, after replacing the copper I was able to join the two pyramids and obtain a reasonable bead of solder.

The sculpture was then spoiled by overenthusiastic washing that caused a few drops of water to smear two of the inside faces. I was not opening the piece again. It has been finished and will be kept in the studio as a reminder of the lessons learned.

Cubes 1

The first 'dimensional' piece I made on the course was a 4 inch cube to my own design standing on a cut off corner.

Once I established my home studio this piece led to more three dimensional pieces that I refer to as my 'Cubic' series. So far there are four designs in the series, worked on at different times and interspersed with other designs.

Cubic 2 was a fairly obvious development, with four corners shaved off.

Part of the fun of working with glass is seeing the effects of light on the piece.

 It is light that brings the work to life.

The body was made in transparent glass with textured green swirls, while smokey grey originally used in Cubic1 was used for the corner panels. When I revisit this design I will use stronger colours to see how it changes the look.

During the course I had planned to make a large piece with all bevels, 4 inch squares and triangles. I'm not sure if I lost the triangles or did not purchase them, as I was selecting quite a bit of glass at the time. Anyhow, Cubic3 now has the square bevels and art glass triangles. The triangles were made from smokey grey and strong wispy blue.

 

While working on the piece I discovered that it looked quite good standing on one of the triangular sides.

An incidental effect is the depth of image provided by the mirrored base.

Bevels add extra dimensions to the light that is transmitted and refracted through the sculpture.

On first sight Cubic3 does not look like a cube. However, imagine that the beveled glass, base and open top are the faces of a 6 inch cube, then cut off all 8 corners to give equilateral triangles.  

I have also been playing with different ways of treating the solder seams. In Cubic1 the solder joints were cleaned and polished. However, the bright silver lines tend to be visually dominant and detract from the glass.

The next step is seen in Cubic2 with the application a copper patina (also used on its contemporary, the three dimensional star). This is an improvement on polished silver, and seemed very good at the time.

Black patina was used on Cubic3. When first applied this is a dead matt black, but finishing compound brings up a deep polish that can be so reflective as to appear silver. Neither was the finish that I was looking for.

Cubic4 came about as an amalgamation of the last of the suspended sculptures and the Cubic series. In fact it is the only true cube! I had set up a cutting jig for the last of the suspended sculptures and cut more two inch squares that were needed. After finishing that piece I decided to try something simpler - so built a cube with a lift off lid. The lid was made from two pieces of glass, laminated together. The glue joint showed in the clear glass so, having just invested in a fusing kiln, I decided to try a fused lid.

  
With this piece I arrived at a suitable treatment for the solder joints that complements the glass. The solder joint is cleaned then polished, copper patina applied and buffed, then black patina is brushed on and quickly washed off. Once dried it is cleaned and polished with two coats of finishing compound. The result is close to weathered bronze with a polished finish.

Suspended Sculptures 1

I find that working on one project usually triggers ideas for more designs. To this end I keep a sketch book devoted to ideas for glass projects. Often, what is eventually made is in itself an evolution of the idea in the sketch book.

My final project on the course was a three dimensional star constructed from square bevels.

While working on it I could see a number of possible developments, primarily by using coloured glass and by changing the shape of the component pieces.

My next step was a combination of the two, using coloured glass in 'kite' shapes that kept the 90° angle for the core of the sculpture.

This resulted in a more obvious star shape, but with the same basic structure. I used wispy amber glass for the vertical arms and a transparent amber with surface texture for the other arms. I also treated the solder with copper patina to get away from the bright silver lines that distract from the colour and texture of the glass (but would all to soon become a dull grey).

 For me the pleasure of glass is seeing it changing the light that shines through it.

The projected sunlight in this image enhances the texture of the glass surface.

A week or two later I decided to extend the basic design using coloured glass squares and bevels. A simple jig was set up to cut a selection of coloured two inch squares (which incidentally inspired another cubic design).

While quite simple in concept this piece proved something of a challenge to construct. I really need a bench vise with a swivel head to hold the pieces for soldering. As it was I made do with the two salvaged computer hard drives, blocks of wood, card and push pins. These enabled me to position the work to keep the joint being soldered horizontal.

The two bevels throw highlights, enhancing the projected colours.

The solder has been treated with a more complicated patina, using copper and black, to give an antiqued finish. While holding the piece and polishing I was reminded of my sextant, with its selection of square coloured filters that could be pivoted over the telescope lens and horizon glass to protect the eyes from the full strength of the sun.

Fantasy in Glass 2

Weeks 3 and 4 of the course were for a three dimensional project. Treece had shown us samples and patterns during the first two weeks, so we knew where we were heading. None of the three who turned up for the third week used one of the class patterns, but all came with our own ideas.

Treece is an expert with decorative solder and ornamentation

At first Treece could not understand my pattern, but then became quite enthusiastic about it. It was a simple cube, standing on a cut (or truncated) corner. This time we had to buy our own glass, so I was overwhelmed by the choice in the shop. 3D or dimensional work is usually done using the copper foil technique. My cube was finished and ready to take home after staying on a bit longer than the scheduled time. I had thought of the sculpture as a candle holder, but was warned that the top would trap heat and might crack the glass.

I needed something for the last week. A web search found an interesting little 3D project. This seemed a good idea as I was not sure if there was a different technique when using bevels. No pattern this time, just the idea in my head and six nice shinny clear square bevels. Unfortunately, Treece came across to see what I was doing just as I realised that I had tack soldered a piece in the wrong position and was melting the joint.

Teaching studio

Figimodo checking my tool kit while I foil a bevel

Eventually it all came together in the correct order, giving a nice little 3D star.

Was the course worth it?
Most definitely, FIG is the place to learn stained glass techniques with a knowledgeable and enthusiastic team. I left each of the last two sessions with glass and tools to set up a basic home studio.